Safety and care

<

Safety and care

Warranty & Quality
The daily use of Elfa storage solutions requires both materials and craftsmanship of the highest quality. We develop products designed to last, and our 10-year warranty is a promise of exactly that.
Elfa products are covered by a 10-year warranty from the date of purchase.

What is covered by the warranty?
The warranty covers defects in materials and workmanship under normal residential use. It also covers functional defects in moving components such as wheels, soft-close mechanisms, and pull-out functions.
This commercial warranty does not affect your statutory rights under applicable consumer protection legislation.

Warranty Provider
The warranty provider is Elfa International AB, Sweden.

How to make a claim
If there is an issue with your product, contact the retailer/store where you made your purchase and bring your receipt. The store will then inform Elfa. We at Elfa will do everything we can to provide a response to your claim as quickly as possible. However, it is important that you report any defect promptly, and therefore we recommend that you unpack and inspect your delivery immediately.
If you cannot bring the product to the store, please take a photo showing the defect. Take one photo from approximately 1 metre away and one close-up photo with a nearby object (for example, a matchbox or pen) for size comparison in the case of surface damage.

How we help you
In the event of an approved claim, Elfa undertakes, at no cost to you as a consumer, to repair or replace the defective product or component.
Repair or replacement of individual parts is prioritised in order to extend the product's lifespan. If this is not possible, the product will be replaced with a new or equivalent item.

Limitations
Naturally, we expect that you take good care of your Elfa products. A product that has been stored, assembled, or used incorrectly is not covered by the warranty. External damage and consequential damage occurring after your delivery has been accepted are not covered by the warranty.

Assembly Instructions

<

Assembly Instructions

You need the following to assemble: Screwdriver/drilling machine, metal saw (if adding top tracks and/or adjusting top track widths), leveller.
Before you start: Make sure you have chosen the right screw/plug for your wall type.The recommendation, when mounting the top track, is to use Elfa hardware. We recommended that a screw should be placed in every hole, for maximum saftey. The screw holes in the top track are shaped oval, in order to increase the probability to find studs to mount in.
Important NOTE: Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these wires or lines, please contact a professional electrician or plumber before drilling.
Step 1 (Mounting the top track): Place the top track at the desired height and mark one hole in the middle. Begin drilling the marked hole with a 3mm (1/8") drill bit. If you hit a stud, continue drilling the entire length of the bit. If you hit the hollow part of the wall, enlarge the hole with a 10mm (3/8") drill bit for anchors. Fasten the top track with a screw and tighten it enough to hold the top track against the wall. Place a leveller on the top of the top track and adjust it as required. Mark all remaining holes.
Step 2 (Hang in the hang standards): Hang in the hang standards onto the bottom "lip" of the top track. In order to fit in the hang standards into the top track, aim for an entry point where there is a cut-out on the upper lip of the top track. Slide the hang standards to their approximate position on the top track. With the end stop at the outer edges of the top track, the hang standard can be placed at the far end of the track.
Step 3 (Adding the extension hang standards): Separate out the screws from the extension hang standard adapter. Bend out the hang standard slightly from the wall and slide the top part of the extension standard adapter into the standard from underneath. Fasten the adapter with one of the screws by using a screwdriver. Slide the small, colour-matching, plastic piece and the extension standard onto the adapter. Fasten with the remaining screw .
Step 4 (Mounting the brackets): Assemble the brackets into the hang standard by leaning the "nose" of the bracket upwards and attaching the upper "teeth" of the backside of the bracket into the slots. Then let the bracket come down.
Step 5 (Mounting the wire shelf): A wire shelf has a top and a bottom. The middle support wire is connected to the bottom of the shelf. Place the bottom of the wire shelf over the notches in the bracket. Install the shelf with end wires inside the brackets. Lock the shelf into place by pressing down on the middle of the shelf and pushing toward the wall.
* To reposition a wire shelf after it’s been attached to the brackets: hold by the brackets, and lift the front of the shelf toward the ceiling and outward to release the entire unit from the hang standards.
* Demount: To remove a wire shelf from a bracket while on the hang standards: hold the hang standard steady with one hand. Place the other hand at the back of the shelf. Pull up and forward to release.
Step 6 (Mounting the closet rod): Insert the closet rod holders into the slot underneath the bracket, by leaning the bottom of the holder slightly upwards and inserting the upper "tooth" of the holder into the slot. The two "flat" closet rod holders are meant to be mounted into the outer brackets. Let the holders come down into place. Once the closet rod holders are mounted, firmly press the end caps into the outer ends of the closet rod. Then snap the closet rod into the closet rod holders.

Assembly Instructions

Classic by Elfa

Starter kit 2 section Clothing white

Recommended price (Prices may vary between retailers)

169,40

Pre-packed Top-hung Click-in storage solution for e.g. closet or laundry storage. Based on two 60-width sections and includes Top track, Hang standards, Extension standards, Adapter, Click-in brackets, Wire shelf, and Closet rod. Can be combined with other storage products in 60-width to create a solution tailored to your needs. Fits behind sliding door solution with Elfa Original Standard sliding doors (2 pcs, width 623 mm).

A great start to your storage – gathered in a practical package.
Quick and easy to mount on the wall.
Complete with additional storage, such as wire shelves or pull-out mesh baskets.

Color

Size

Needs To Have

Classic by Elfa

Screw and plug, pkg/10

5,80

Classic by Elfa

Drywall anchor, pkg/5

8,00

Safety and care

<

Safety and care

Warranty & Quality
The daily use of Elfa storage solutions requires both materials and craftsmanship of the highest quality. We develop products designed to last, and our 10-year warranty is a promise of exactly that.
Elfa products are covered by a 10-year warranty from the date of purchase.

What is covered by the warranty?
The warranty covers defects in materials and workmanship under normal residential use. It also covers functional defects in moving components such as wheels, soft-close mechanisms, and pull-out functions.
This commercial warranty does not affect your statutory rights under applicable consumer protection legislation.

Warranty Provider
The warranty provider is Elfa International AB, Sweden.

How to make a claim
If there is an issue with your product, contact the retailer/store where you made your purchase and bring your receipt. The store will then inform Elfa. We at Elfa will do everything we can to provide a response to your claim as quickly as possible. However, it is important that you report any defect promptly, and therefore we recommend that you unpack and inspect your delivery immediately.
If you cannot bring the product to the store, please take a photo showing the defect. Take one photo from approximately 1 metre away and one close-up photo with a nearby object (for example, a matchbox or pen) for size comparison in the case of surface damage.

How we help you
In the event of an approved claim, Elfa undertakes, at no cost to you as a consumer, to repair or replace the defective product or component.
Repair or replacement of individual parts is prioritised in order to extend the product's lifespan. If this is not possible, the product will be replaced with a new or equivalent item.

Limitations
Naturally, we expect that you take good care of your Elfa products. A product that has been stored, assembled, or used incorrectly is not covered by the warranty. External damage and consequential damage occurring after your delivery has been accepted are not covered by the warranty.

Assembly Instructions

<

Assembly Instructions

You need the following to assemble: Screwdriver/drilling machine, metal saw (if adding top tracks and/or adjusting top track widths), leveller.
Before you start: Make sure you have chosen the right screw/plug for your wall type.The recommendation, when mounting the top track, is to use Elfa hardware. We recommended that a screw should be placed in every hole, for maximum saftey. The screw holes in the top track are shaped oval, in order to increase the probability to find studs to mount in.
Important NOTE: Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these wires or lines, please contact a professional electrician or plumber before drilling.
Step 1 (Mounting the top track): Place the top track at the desired height and mark one hole in the middle. Begin drilling the marked hole with a 3mm (1/8") drill bit. If you hit a stud, continue drilling the entire length of the bit. If you hit the hollow part of the wall, enlarge the hole with a 10mm (3/8") drill bit for anchors. Fasten the top track with a screw and tighten it enough to hold the top track against the wall. Place a leveller on the top of the top track and adjust it as required. Mark all remaining holes.
Step 2 (Hang in the hang standards): Hang in the hang standards onto the bottom "lip" of the top track. In order to fit in the hang standards into the top track, aim for an entry point where there is a cut-out on the upper lip of the top track. Slide the hang standards to their approximate position on the top track. With the end stop at the outer edges of the top track, the hang standard can be placed at the far end of the track.
Step 3 (Adding the extension hang standards): Separate out the screws from the extension hang standard adapter. Bend out the hang standard slightly from the wall and slide the top part of the extension standard adapter into the standard from underneath. Fasten the adapter with one of the screws by using a screwdriver. Slide the small, colour-matching, plastic piece and the extension standard onto the adapter. Fasten with the remaining screw .
Step 4 (Mounting the brackets): Assemble the brackets into the hang standard by leaning the "nose" of the bracket upwards and attaching the upper "teeth" of the backside of the bracket into the slots. Then let the bracket come down.
Step 5 (Mounting the wire shelf): A wire shelf has a top and a bottom. The middle support wire is connected to the bottom of the shelf. Place the bottom of the wire shelf over the notches in the bracket. Install the shelf with end wires inside the brackets. Lock the shelf into place by pressing down on the middle of the shelf and pushing toward the wall.
* To reposition a wire shelf after it’s been attached to the brackets: hold by the brackets, and lift the front of the shelf toward the ceiling and outward to release the entire unit from the hang standards.
* Demount: To remove a wire shelf from a bracket while on the hang standards: hold the hang standard steady with one hand. Place the other hand at the back of the shelf. Pull up and forward to release.
Step 6 (Mounting the closet rod): Insert the closet rod holders into the slot underneath the bracket, by leaning the bottom of the holder slightly upwards and inserting the upper "tooth" of the holder into the slot. The two "flat" closet rod holders are meant to be mounted into the outer brackets. Let the holders come down into place. Once the closet rod holders are mounted, firmly press the end caps into the outer ends of the closet rod. Then snap the closet rod into the closet rod holders.

Assembly Instructions

Nice To Have

Garage+

Track set original 1240 mm

Complete your Original fixed sliding doors with the track set that matches the overall width of your wardrobe. Track set 1240 mm fits two Original door leaves 623x2350 mm.

Configured Price

Original Silver Spegel 623x2350mm

Original Silver Spegel 623x2350mm

Garage+

Door blade original 623x2350 mm

Make it easy to build a sliding door wardrobe with our fixed sliding doors.

Configured Price

Classic by Elfa

Top track cover

Elevate your system with the decorative top track cover. Conceals screws and holes for a polished finish.

Price from 2,50

Classic by Elfa

Closet rod holder set for starter kit

Add more hanging space to your Elfa 2-Section Starter Kit. Holders are designed to fit within the width of a 2-section wardrobe solution with Elfa standard doors.

Price from 8,70

Classic by Elfa

Shelf hook

Optimize storage with our versatile shelf hooks. Ideal for hanging various accessories, like bags.

Price from 11,80

Classic by Elfa

Bracket hook rack

Discover new storage opportunities with our hook rack. Provides easy access and extra hanging options, when mounted on the side of a bracket click-in in corresponding depth.

Price from 11,00

Classic by Elfa

Bracket cover click-in

Avaliable in 3 sizes

Enhance your system with bracket cover. Clean look, protection.

Price from 3,00

Classic by Elfa

Valet rod

Avaliable in 2 sizes

Make the most of limited-depth spaces. Allows you to hang your clothes efficiently, with hangers placed behind each other. Mount under a wire shelf or a wire shelf basket in corresponding depth.

Price from 17,90

Side panel

Avaliable in 3 sizes

Complete your sliding doors with frame sides to create an end piece or freestanding wardrobe.

Configured Price