ELFA Décor Plus Light Monteringsklämma Matt Vit V3

Ett sovrum med en Décor+ by Elfa garderob i vitt som har skjutdörrar med glasfyllning.

Safety and care

Warranty & Quality
The daily use of Elfa storage solutions requires both materials and craftsmanship of the highest quality. We develop products designed to last, and our 10-year warranty is a promise of exactly that.
Elfa products are covered by a 10-year warranty from the date of purchase.

What is covered by the warranty?
The warranty covers defects in materials and workmanship under normal residential use. It also covers functional defects in moving components such as wheels, soft-close mechanisms, and pull-out functions.
This commercial warranty does not affect your statutory rights under applicable consumer protection legislation.

Warranty Provider
The warranty provider is Elfa International AB, Sweden.

How to make a claim
If there is an issue with your product, contact the retailer/store where you made your purchase and bring your receipt. The store will then inform Elfa. We at Elfa will do everything we can to provide a response to your claim as quickly as possible. However, it is important that you report any defect promptly, and therefore we recommend that you unpack and inspect your delivery immediately.
If you cannot bring the product to the store, please take a photo showing the defect. Take one photo from approximately 1 metre away and one close-up photo with a nearby object (for example, a matchbox or pen) for size comparison in the case of surface damage.

How we help you
In the event of an approved claim, Elfa undertakes, at no cost to you as a consumer, to repair or replace the defective product or component.
Repair or replacement of individual parts is prioritised in order to extend the product's lifespan. If this is not possible, the product will be replaced with a new or equivalent item.

Limitations
Naturally, we expect that you take good care of your Elfa products. A product that has been stored, assembled, or used incorrectly is not covered by the warranty. External damage and consequential damage occurring after your delivery has been accepted are not covered by the warranty.

Assembly Instructions

Installation of LED lighting in hang standards:
Step 1: Pull the lighting cables through the hang standards. Feed the connector ends through the correct slots where you plan to place your lighting (according to your layout plan).
A branching lighting cable is connected to the cable from the light fitting. If you have more than one light, the other end is used to connect to an additional lighting cable. (Only one end goes through the slot.)
Tip: Fold back the connector ends so that they do not fall back through the slots.
Step 2: Turn the hang standard so that the back side is facing up. Use 3–4 cable organizers along the cable. The cable should lie in the centre grooves of the cable organizers.
Step 3: Connect as many lighting link cables as needed to reach the bottom of the hang standard. At least 75–100 mm (3–4") should extend below the bottom of the hang standard.
Step 4: Press down the clips on the back of the hang standard so that they are flush.
Note: If you are using an extension standard, cables can be routed down in the same way.
Step 5: Your lighting cable box should contain the transformer. Install it close to the wall socket or at the bottom of the hang standards. The transformer and power supply cable can lie loose in the cable box or be secured using the included double‑sided tape.
Step 6: Install the lighting cable box next to the connector end of the lighting cable hanging out from the bottom of the hang standard. Connect the connectors.
Note: Do not connect the power supply to the wall socket yet.
Step 7: Attach the lid of the lighting cable box by pressing it onto the cable box.

Installation of LED lighting under wall cabinets:
LED light fittings are attached to the underside of the wall cabinets using strong magnets.
Route the cable from the light fitting along the edge under the cabinet towards the back wall.
Feed the cable end through the hole in the lower corner of the cabinet.
Connect the connector end to the connector end of the lighting cable coming from the hang standard.
If you have several cabinets next to each other, the light fittings can be connected in series.
Place the lighting cables along the edges under the cabinets and route them through the holes to the next cabinet.

Installation of LED lighting under wire shelf:
Place the included mounting clip over the wire as shown in the illustration.
Press until you hear a “click”.
Route the lamp cable to the brackets and connect it to the lighting cable in the hang standard.

Assembly Instructions

Garage+

Lighting W: 60

Recommended price (Prices may vary between retailers)

52,00

Elevate your workspace with Garage+ LED lighting fixture. Its magnetic base allows for effortless installation under cabinets, on standards, or even on a pegboard. Illuminate your tasks with a bright, white light that enhances your working conditions. The package includes two foam cable locks, ensuring a tidy setup inside the standard.

Illuminate your workspace with bright, white light for optimal working conditions., The magnetic design enables hassle-free mounting on various Garage+ elements., Foam cable locks let you hide the cables inside the Garage+ standard.

Color

Size

Needs To Have

Garage+

Power supply kit White

147,20

Garage+

Dimmer White

40,80

Décor+

Lighting link cable 100 cm, pkg/4

28,60

Safety and care

Assembly Instructions

Specification

Technical description

Assembly Instructions

Lighting W: 60

52,00

Select size

Specification

Technical description

Assembly Instructions